DIY LOCKER CABINET AS SEEN ON HGTV’S OPEN CONCEPT!

Hey friends!  Thanks so much for your continued support of our pilot Open Concept on HGTV!  You can see lots of before and after shots of the remodel by  I am here today to share the free plans and tutorial for the DIY Locker Cabinet!  Here it is in their home!

Locker Cabinet from HGTV Open Concept

Locker Cabinet HGTV Open Concept

Isn’t it GORG?  I love it.  As always, I will walk you through the entire build here.  You can also download and print the free plans by clicking HERE or the button below!

 

Let’s get started!

The majority of this piece uses hardwood plywood.  What the heck is that?  Good question!  Hardwood plywood is plywood that comes in 4′ x 8′ sheets and s0me smaller sizes.  Our very favorite brand to use is Purebond Plywood.  You can find it at Home Depot.  The outside layer of the plywood is a hardwood veneer like oak or birch. So, you get the look of a hardwood at the cost of plywood.  Can’t beat that people!  Plus, it’s super straight making it easy to work with which makes me happy!

The plywood sheets are big, and often impossible to fit into your car… Especially when you have 5 kids in the back ????  We like to have Home Depot make the rip cuts for us in order to get it in the car at home.

Home Depot cut wood

Once I had it home, I made most of my other cuts using Kreg’s RipCut.  This is a really cool attachment that fits onto your circular saw.  You can adjust it to make straight cuts at certain measurements.  It’s very accurate and easy to use.

Kreg Rip Cut

MORE POPULAR ARTICLES

1. DIY Valentine’s for Kids and Adults!

2. How To Make A Key Pouch From a Coin Purse

3.  How To Make A Stress Ball

4.  7 Simple Tips to Decorate Your Living Room on a Budget

5.  How to Make Your Own DIY Industrial Sconces

Really this build is very simple.  It’s big… But, simple. You build the box of the sideboard first, and then add the trim and the doors.  For the box, I used my Kreg Jig.

Kreg Jig K5 Model

First, you will build the frame of the cabinet.  These are your bottom, top and side pieces.

Frame of Locker System

I used 3/4″ pocket holes and 1.25″ pocket hole screws for all of my joints.  I also used a line of Titebond 3 wood glue on each joint.

Next, you will add your vertical dividers.  I like to mark the placement of mine with pencils and use a speed square to make sure the placement is right.

Locker System Dividers

After adding the vertical dividers, I added my shelf pieces.  You can add these at whichever height best fits your storage needs.  You can see below my placement of the pocket holes.

Shelves of console table

Build a console table using a Kreg Jig

Buffet Table How To

Shelves for locker system

I also decided to add a small piece in the middle to serve as a brace for the weight to keep it from sagging.  I plan to fill this baby up with dishes!  I did this by cutting a small piece of the plywood and attaching it with wood glue and pocket hole screws.

Console table base

You will use a drill with the Kreg bit to attach all of these screws.  The bit is included with the Kreg Jig.  I used my Ryobi 18V One+ drill for mine.  WE LOVE THIS DRILL.  It’s the perfect size and has a ton of power.  I actually have 2 to keep me from switching bits… #lazygirlprobs ????

Attaching shelves of buffet

Once you have the entire box assembled you will add your trim pieces.  First, build out the face frame.  I also used 3/4″ pocket holes and 1.25″ pocket hole screws on this part.

Face Frame

Kreg Pocket Holes

I then attached the face frame to the cabinet front.

Back of Locker System

I used 1.25″ pocket hole screws through the bottom pocket holes, and I also used my Ryobi 16V Finish Nailer for this part.  Yes… A battery finish nailer.  It’s amazing.  You need it too.

Ryobi 16G Finish Nailer

The base of my sideboard looked like this….

bottom of buffet table

And it’s framed!

How to build a buffet table

The back uses 1/4″ Purebond Plywood.  I have Home Depot cut this down for me as well.  This is best attached using an 18g stapler, but you can also use a finish nailer.

Back of cabinet

To create the doors, I used my Kreg Jig as well.  I made the pocket holes on my shorter pieces and attached them to the longer ones using 1.25″ pocket hole screws.

Although we give you guys the cuts for these doors, I always like to measure the opening before making the cuts to be sure on the size.  I like to make the doors 1/8″ smaller all around, which would be 1/4″ smaller than the width and height of each opening.  For the doors, you will have 4 longer pieces without pocket holes like this.

long door pieces

You will also have 4 smaller pieces each with pocket holes on both ends like  this.

short door pieces

I attached these pieces using wood glue and 1.25″ pocket holes screws  to create rectangles.

Door Frame for Locker System

building cabinet doors

Each door looks like this!

Door Frame for Coffee Cabinet

Then, cover each door back with a piece of 1/4″ Purebond Plywood and attach using wood glue and 3/4″ brad nails.

Back of Doors

I cut the horizontal trim pieces to size and attached them using wood glue and brad nails from the back of the door into the trim pieces.

Next, I built and attached the planked top.  I created the plank top by using 3/4″ pocket holes down 4 of my 5 boards.  Then, I used 1.25″ pocket hole screws through those to attach it all.

Plank top Buffet Table

Before attaching it to the top I added a bunch of wood glue to the top of my sideboard.  I had a little fun with this part…

Wood glue for the top of the buffet

To attach the top, I used my new (and wonderful) Kreg bar clamps.  I love easy bar clamps.  These are so awesome… They are self adjusting and easy to use.   I used mine to hold the top in place while I used the finish nailer to attach the top with 1.25″ finish nails.

Kreg Bar Clamp

This is what she looks like all finished up and ready for paint!

Doors

Finished Locker Cabinet

I used an AMAZING color on this piece.  It’s called Urbane Bronze by Sherwin-Williams… Seriously, it’s the perfect dark grey.

Sherwin-Williams Urbane Bronze

I found my hardware at Home Depot.

These are the Liberty Hardware pulls I used!

Liberty Hardware Pull

I used my drill to attach everything.

Hardware for Cabinet

I also added a hook to the inside of each cabinet so the kids could hang their backpacks and stuff.  And, here it is all finished and on display!

Locker Cabinet HGTV Open Concept

Locker Cabinet from HGTV Open Concept

What do you think?  I may go take it back I love it so much ?

Leave a Reply

Your email address will not be published. Required fields are marked *